Quick Menu
Q&A
CATALOGUE
SELECTION GUIDE
- English
- Japanese
- Russian
- Spanish
CORP.DATA
- Profile(ENG)
- Profile(JPN)
- CORP.INFO(ENG)
REGISTER
INQUIRY
PRODUCTS
SENSORS
CONTROLLERS
MOTION DEVICE
MENICS PRODUCTS
PA PRODUCTS
CONTROL SWITCHES
I/O TERMINAL BLOCK / CONNECTOR / CABLE
  
Sensing, the starting point of all automation, and Autonics is always there for you.
BMS Series
Sensors
High Speed Response Type with Built-in Output Protection Circuit
BMS Series is a photo sensor that has capability to switch between Light On and Dark On modes and has a fast response rate of under 1ms. Various detection types including diffuse reflective type, through beam type, retroreflective type allow more diverse user application area.

Product DetailData sheet2D/3D CAD Data
Main Features

● Reverse power polarity and overcurrent
● High speed response : Max. 1ms
● Light ON/Dark ON mode selectable by control wire
● Built-in the sensitivity adjustment VR
   (Except for through-beam type)


Ordering Information

 


Specification Table

Model NPN open collector output BMS5M-TDT BMS2M-MDT BMS300-DDT
PNP open collector output BMS5M-TDT-P BMS2M-MDT-P BMS300-DDT-P
Sensing type Through-beam Retroreflective Diffuse reflective
Sensing distance 5m 0.1 to 2m ※1 300mm ※2
Sensing target Opaque materials of Min. ø10mm Opaque materials of Min. ø60mm Translucent, Opaque materials
Hysteresis - Max. 20% at rated settingdistance
Response time Max. 1ms
Power supply 12-24VDC ±10%(Ripple P-P : Max. 10%)
Current consumption Max. 50mA Max. 45mA
Light source Infrared LED(940nm)
Sensitivity adjustment - Adjustable VR
Response time Selectable Light ON or Dark ON by control wire
Control output NPN or PNP open collector output
• Load voltage : Max. 30VDC
• Load current : Max. 200mA
• Residual voltage - NPN : Max. 1V, PNP : Max. 2.5V
Protection circuit Reverse power polarity, Output short-circuit(Overcurrent) protection circuit
Indicator Operation indicator : red LED, Power indicator : red LED(BMS5M-TDT1)
Insulation resistance Min. 20MΩ(at 500VDC megger)
Noise resistance ±240V the square wave noise(pulse width : 1㎲) by the noise simulator
Dielectric strength 1000VAC 50/60Hz for 1 minute
Vibration 1.5mm amplitude or 300m/s2 at frequency of 10 to 55Hz(for 1 min.) in each of X, Y, Z directions for 2 hours
Shock 500m/s2(approx. 50G) in each of X, Y, Z directions for 3 times
Environ- ment Ambient Illumination Sunlight : Max. 11,000㏓, Incandescent lamp : Max. 3,000㏓
Ambient temperature -10 to 60℃, storage : -25 to 70℃
Ambient humidity 35 to 85%RH, storage : 35 to 85%RH
Material Case : ABS, Sensing part : Acrylic (Through-beam : PC)
Cable ø5, 4-wire, Length : 2m(Emitter of through-beam type: ø5, 2-wire, Length : 2m)
(AWG22, Core diameter : 0.08mm, Numner of cores : 60, Insulator out diameter : ø1.25)
Accessories Individual - Reflector(MS-2),
VR adjustment driver
VR adjustment driver
Common Mounting bracket, Bolts/nuts
Approval CE
Unit weight Approx. 180g Approx. 110g Approx. 100g
※1: It is mounting distance between sensor and reflector MS-2 and it is same when MS-5 is used. It is detectable under 0.1m.
※2: It is for Non-glossy white paper(100x100mm)
※ The temperature or humidity mentioned in Environment indicates a non freezing or condensation environment.



Dimensions


Connections




User's Guide




Caution for your safety